Tianyida Technologies Limited
5 1

VS-S2T-10G Core Network Switch Cisco Catalyst 6500 10G Series Supervisor Engine 2T

Contact Now* Send an Inquiry to this supplier.
or
Start Order * Name your price

Contact us

Tianyida Technologies Limited
[China]

Address
Room1606,16/F.,Workingbond Commercial Center, 162-164 Prince Edward Road,MONGKok,Kowloon, Hong Kong Shenzhen Guangdong
Phone
86-180-17468761
Contact name
sunny

Quick Information

  • Brand Name: CISCO
  • Place of Origin: China
  • Model Number : VS-S2T-10G

Description

VS-S2T-10G Core Network Switch Cisco Catalyst 6500 10G Series Supervisor Engine 2T

 

Description:Cat 6500 Sup 2T with 2 x 10GbE and 3 x 1GbE with MSFC5 PFC4


VS-S2T-10G is Cisco Catalyst 6500 Series Supervisor Engine 2T. The Supervisor Engine 2T is designed to deliver higher performance, better scalability, and enhanced hardware-enabled features. Supervisor Engine 2T integrates a high-performance 2-Terabit crossbar switch fabric that enables 80 Gbps switching capacity per slot on all Cisco Catalyst 6500 E-Series Chassis. This VS-S2T-10G is similar with the VS-S2T-10G=. Both of them has the same price, same appearance, same functions and specifications. The only difference is that the VS-S2T-10G= is a spare one.

 

Product Code VS-S2T-10G
Chassis compatibility Supported on all Catalyst 6500 E-series chassis and Catalyst 6807-XL chassis
Switch fabric 2.08 Tbps Crossbar Switch Fabric with 26 Fabric Channels
Software compatibility 12.2(50)SY
Uplink ports (PORT 1 through PORT 5) ·Five uplink ports:
·Two 10GBASE-X ports
·Three 1000BASE-X ports
·Each uplink port has a link LED associated with it.
Console ports One console port (RJ-45)
Compact Flash 1GB
DRAM 2GB for Lite and XL (4GB upgrade with 2GB memory upgrade (2+2)
NVRAM 4 MB
switching capacity up to 80 Gbps per slot of switching capacity on E-Series chassis
Routes 256K (IPv4)
128K (IPv6)
Netflow entries 512K
Layer-3 classification and marking access control entries (ACEs) 64K shared for QOS / Security
Layer 2 rate limiters 20 ingress/6 egress
Security ACL entries 256K shared for QOS/Security
Power requirement (at 42 VDC) 10.36 A
Dimensions (H x W x D) 1.73 x 14.4 x 16.0 in. (4.4 x 36.6 x 40.6 cm). Occupies one slot in the chassis
Weight 12.0 lb (5.44 kg)
 

 

 

 

Figure 1 Supervisor Engine 2T Front Panel Features

 

 

 

          

                                                                             

 

1 STATUS LED 8 1000BASE-X UPLINK ports (requires SFP transceivers)
2 ID LED 9 MANAGEMENT port
3 SYSTEM LED 10 CONSOLE port
4 ACTIVE LED 11 10GBASE-X UPLINK ports (requires X2 transceivers
5 PWR MGMT LED 12 USB port
6 RESET switch 13 Port currently not supported
7 PCMCIA slot    

 

 

Table 2   lists and describes Supervisor Engine 2T features.

 

Table 2  Supervisor Engine 2T Features

 

 

Feature Description
Chassis compatibility Supported only on all Catalyst 6500 E-series chassis.
Software requirements (minimum) 12.2(50)SY
Fan trayrequirements Both versions of the Supervisor Engine 2T require that a high-speed fan tray be installed in the chassis.
Note Low-speed fan trays do not provide sufficient cooling for Supervisor Engine 2T.
Slot installation restrictions Supervisor Engine 2T must be installed in:
Slots 1 and 2 in a 3-slot or a 4-slot chassis
Slots 5 and 6 in a 6-slot or a 9-slot chassis
Slots 7 and 8 in a 13-slot chassis
Note The primary supervisor engine can be installed in either slot.
Note When the Supervisor Engine 2T is installed in a chassis with either a WS-X69xx or a WS-X68xx module, there is a requirement that the two slots adjacent to the supervisor engine and the module either have a module installed in them or, if the slots are unused, have a switching-module filler plate (Cisco part number SLOTBLANK-09 or WS-X6K-SLOT-CVR-E) installed for NEBS compliance. Do not use blank slot covers (WS-X6K-SLOT-CVR) to cover the adjacent unused slots.
Hardware restrictions Supported only in Catalyst 6500 E-series switches.
Supports only modules equipped with the DFC4-A, DFC4-AXL, DFC4-E, DFC4-EXL, or the CFC daughter cards. Modules equipped with DFC3 daughter cards are not supported. For further information on hardware restrictions and module support, refer to the software release notes at the following URL:
Memory  
DRAM 2 GB
External CompactFlash (disk0) Compact flash Type 2 (1 GB)
Front panel features  
RESET switch The RESET switch allows you to reset and restart the switch.
Note Because the reset switch is recessed in the supervisor engine faceplate, you must use a ballpoint pen tip or other small, pointed object to access the switch.
CONSOLE port This is a 10/100/1000 port that uses an RJ-45 connector. The CONSOLE port allows you to access the switch either locally (with a console terminal) or remotely (with a modem). The CONSOLE port is an EIA/TIA-232 asynchronous, serial connection with hardware flow control.
Universal Serial Bus(USB) port Two USB 2.0 ports are provided. The USB 5-pin mini Type-B connector is used as a console port allowing attachment to PCs that are not equipped with an RS-232 interface. The second USB port is currently not supported.
MANAGEMENT port A 10/100/1000 copper port used for out-of-band Ethernet management of the switch.
DISK 0 slot and LED One PCMCIA slot is available. The PCMCIA slots allow a Flash PC card to be installed providing additional flash memory. You can use this flash memory to store and run software images or to serve as an I/O device. An eject button is located on the left side, next to each slot. Pushing in on the button ejects the Flash PC card from the slot. The slot supports 1 GB Flash PC cards.
The PCMCIA slot has an activity LED associated with it.
 
Uplink ports (PORT 1 through PORT 5)
Supervisor Engine 2T has five uplink ports:
Two 10GBASE-X ports
Three 1000BASE-X ports
Note The two 10GBASE-X ports require X2 transceiver modules; the three 1000BASE-X uplink ports require SFP transceiver modules. For X2 and SFP transceiver support, refer to the compatibility matrices at the following URL:
Note In chassis configurations where there are redundant supervisor engines installed, the uplink ports on the supervisor engine that is in standby mode are fully functional.
Each uplink port has a link LED associated with it.
 
Uplink port queue structure

 

1000BASE-X (uplink ports 1, 2, and 3)
Tx—1p3q4t
Rx—2q4t
10GBASE-X (uplink ports 4 and 5)
With ports 1, 2, and 3 enabled: Tx—1p3q4t, Rx—2q4t
With ports 1, 2, and 3 disabled: Tx—1p7q4t, Rx—8q4t
1 port group
Pluggable transceivers Supports SFP 1000BASE-X transceivers in Ports 1, 2, and 3.
supported Supports X2 10-GBASE-X transceivers in Ports 4 and 5.
  Note For additional information about SFP and X2 transceiver support, see the compatibility matrices listed on this page:
  Also see Appendix A for descriptions of the X2 and SFP transceivers.
Hardware-based forwardingengine (Policy Feature Card) VS-S2T-10G—PFC4 (VS-F6K-PFC4)
VS-S2T-10G-XL—PFC4XL (VS-F6K-PFC4XL)
Multilayer Switch Feature Card (MSFC) daughter card versioninstalled MSFC5 (VS-F6K-MSFC5)

 


Contact us


Thanks for your visiting! If you are interested in our products or have any question, please contact us online or click " send " the inquiry, we will reply you promptly !

 


Product Image

  • VS-S2T-10G Core Network Switch Cisco Catalyst 6500 10G Series Supervisor Engine 2T image

Other products from this supplier

Send an Inquiry to this supplier

Send an Inquiry to this supplier
* From
  To sunny
Tianyida Technologies Limited
* Buying Product
- Please enter your specific buying item.
e.g. 42 inch LCD TV, leather executive chair
Category : Resistors
* Message

Use English only Max. 2000 characters. (Min. 20)

Send
EC21.com does not guarantee the validity of product information or the credentials of sellers.